How Warman Slurry Pump Works? - Warman® slurry pump
Warman®, head office The Weir® Group PLC, was founded in 1871 with two brothers, George and James Weir in the West Coast of Scotland. Weir® Minerals now is one of the world leaders in pumps, mill liners, cyclone, slurry valve, screens which are highly used for mineral processing industries.
Warman® slurry pump is covered with horizontal slurry pump and vertical slurry pump, with models of AH slurry pump, HH slurry pump, L slurry pump, GSL slurry pump, WBH slurry pump, MCR slurry pump, XU slurry pump, SP slurry pump, G slurry sand pump, SPR slurry pump, AHR slurry pump.
Warman® slurry pump is one of the best manufacturers in supplying the most comprehensive range of slurry pumps, the slurry pumps, which China Slurry Pump Do® Pump has listed above, are highly used for mining, mineral processing, dewatering, recycling, floating, sand dredging, and chemical industries, slurry pumps are acting as heavy duty mining equipment apply for mill discharge, tailing, cyclone, filter press, processing plant, tailing, slurry recycling systems.
How Warman® Slurry Pump Works? - Safety Operation
China Slurry Pump - Do® Pump is introduction how a Warman® slurry pump works, the safety operation process must be complied with all times of Warman® slurry pump operation, which must be carefully observed and followed with correct procedures, in order to avoid injury and damage to equipment and slurry pump users.
How Warman® Slurry Pump Works? - Step One
Do Not Apply Heat To The Impeller Hub Or Inlet Eye To Assist Impeller Removal. Application Of Heat May Result In Shattering Of The Impeller , Resulting In Injury Or Equipment Damage.
When assemble or disassemble the slurry pump, China Slurry Pump Do® Pump strongly suggest the impeller hub or inlet eye of the impeller can not be heated to remove, the slurry impeller is in overall heating process when casting and heating process, while partial heating to impeller hub or inlet eye of the slurry pump impeller will cause the impeller broken or damage.
How Warman® Slurry Pump Works? - Step Two
Do Not Operate The Slurry Pump For An Extended Time With Zero Or Very Low Flowrate. Failure To Observe This Warning Could Result In Overheating Of The Pump, And Vaporisation Of The Pumped Fluid, With Generation Of Very High Pressures. Serious Injury To Personnel, Or Damage To Equipment May Result From Such Action.
China slurry pump Do® Pump advice slurry pump users to be aware of the pump safety operation process, when slurry pump is operating in very low or zero flow rate, the air in slurry pump will be overheated, the vaporisation of the liquid and air will create a high pressure, when the pressure is higher than the bear of the slurry pump casing, the slurry pump may explode which result of the damage of the slurry pump, or even injury to slurry pump users.
How Warman® Slurry Pump Works? - Step Three
Check Drive Motor Rotation Prior To Fitting Of Drive Belts Or Couplings. Incorrect Motor Rotation May Cause Personnel Injury Or Equipment Damage.
Warman® slurry pump must rotate in right way of direction, slurry pump is normally rotating in anti-clock way from the suction side of the slurry pump, China Slurry Pump Do® Pump is normally release the coupling screw bolts or the belt from the pump and attached motor when delivering the slurry pump, when slurry pump arrive at working site, the slurry pump operation people should test the motor direction first, then connect the coupling screw bolts or belt with the slurry pump and engine motor, in order to double confirm the pump is working at the right direction, the engine should be immediately stopped after the engine rotating direction is tested again.
How Warman® Slurry Pump Works? - Step Four
Do Not Feed Very Hot Or Very Cold Fluid Into A Pump At Ambient Temperature. Thermal Shock May Result In Fracture Of Pump Wet-End Parts.
China slurry pump Do® Pump suggest that when the Warman® slurry pump is operating, do not feed very hot slurry or very cold fluid into the slurry pump, which the large difference of the temperature, slurry pump wet end parts, including slurry pump impeller, slurry pump volute liner, slurry pump throatbush, slurry pump frame plate liner, may result in broken or damage.
How Warman® Slurry Pump Works? - Summary
Overall, China slurry pump Do® Pump introduced how Warman® slurry pump works in what is Warman® slurry pump and four steps of Warman® slurry pump safety operation process.
Warman® slurry pump is considered as a rotating centrifugal equipment which will result working pressure inside of the pump, the pressure can result of slurry pump working pressure transferring slurry from one point to another, on the other hand, the pressure can also be a danger to damage the slurry pump and injury slurry pump users. Therefore the safety operation must be observed during slurry pump installation, operation and maintenance.
More than that, all auxiliary equipment is associated with slurry pump must be consulted with the slurry pump installation, operation and maintenance. For more information about how Warman® slurry pump works, welcome to contact China Slurry Pump Do® Pump Consultant.
